Cold Rolled Strip Steel Physical Properties; ASTM A109:Temper Bend Test Requirement; No. 1 Hard Not required to make bends in any direction:No. 2 Half-Hard Bend 90 degrees transverse around a radius equal to that of the thickness. No. 3 Quarter-Hard
ASTM 1030 Steel - ASTM 1030 Steel Supplier Steel The soft spheroidized annealed product is processed to give the lowest hardness for maximum formability. This grade of steel is used for machinery parts, brackets, brakes, clips, clutches, springs, washers and for a wide range of uses that can make use of its
Nov 04, 2017 · CRCA is an abbreviation of cold rolled close anneal. This is a steel grade in which cold rolling is done after hot rolling and pickling, to reduce the thickness of steel. Cold rolling makes the material hard. This cold rolled steel is then annealed in a closed container where nitrogen or any other non-oxidizing gases softens it for use and also guards it against oxidation.
Cold Rolled Low Carbon Steel Strip DC04Strips pickled, cold rolled, galvanized - Marcegaglia. EN 10139 Cold rolled uncoated mild steel narrow strip for cold forming DC01 LC/C290÷690 DC03 LC/C290÷590 DC04 LC/C290÷590 DC05, DC06 EN 10132-3 Steels for quenching and tempering (cold rolled narrow steel strip for heat treatment) C22E, C30E, C35E, C40E, C45E, C50E, C55E, C60E, 25Mn4, 25CrMo4, 34CrMo4, 42CrMo4 EN 10132-4
Cold Rolled Steel Sheet for Drawing EN 10130 DC01 DC06Cold rolled steel sheet for drawing and forming applications is produced in a broad spectrum of grades The tensile test is carried out as described in EN 10002 Part 1 using type 2 specimens (initial gauge length Lo = 80mm). Yield strength is determined by the 0,2% off-set method. The test pieces are
Cold rolled strip is used in a variety of applications. It meets high demands on forming behaviour, dimensional tolerances and surface finish, which offers our customers decisive advantages! HFP cold rolled strip is ideally suited for all stamping, bending, drawing and deep drawing purposes.
Cold rolled grades - WilkeMA with finish RR, RM, RL acc. to DIN EN 10139:MB (1) with finish RL, RM acc.to DIN EN 10139:Dimensional tolerances:Acc. to DIN EN 10140 and special agreement:Delivery forms:Coils and cut lengths (1) = MB for thicknesses 0.2 - 2.0 mm, thicker dimensions on request (2)
Cold rolled steel - DC01, DC03, DC04, DC05, DC06 - also ED Cold rolled steel is excellent for cold forming. This product group assigned the grades DC01 to DC07, DC01EK to DC06EK, DC03ED to DC06ED and S215G to S325G. The grades are classified according to the maximum permissible yield strength and can be subdivided as follows. DC01 This grade can be used for simple forming work, for example Bending, embossing, beading and pulling are used.
Classification:Non-alloy quality steel. Standard:EN 10130:2006 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions. EN 10139:1997 Cold rolled uncoated mild steel narrow strip for cold forming. Technical delivery conditions. EN 10152:2009 Electrolytically zinc coated cold rolled steel flat products for cold forming.
DC01 Cold Rolled Steel - Gnee steelCold rolled steel according DIN EN 10130, 10209 and DIN 1623. One of the leading Mild Steel Strip suppliers in the China, supplying DC01 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1, DC03 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1/CS3 and DC06 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold
EN 10130 DC01 Steel 1.0330+ZE Material Data Sheet DC01 steel (1.0330 material) is a European standard cold-rolled quality low-carbon steel flat product for cold forming. In BS and DIN EN 10130 standard, it contains 5 other steel grades:DC03 (1.0347), DC04 (1.0338), DC05 (1.0312), DC06 ( 1.0873) and DC07 (1.0898), the surface quality is divided into 2 types:DC01-A and DC01-B.
Note:In the MS grades, there may be presence of residual / tramp elements ( Such as Cr, Ni, Cu, Mo etc.) upto 0.20% and Al upto 0.07%. Besides the above, other grades in mild steel category can also be supplied depending upon the order quantity and availability of appropriate raw material.
wiretec GmbH ::for Deep DrawingGrade:DC04 - Annealed (A) - Annealed and skin passed (LC) - Cold rolled (C 290, C 340, C 390, C 440, C 490, C 590) C10 Standards:For dimension and shape tolerances:EN 10140 For technical conditions DC04:EN 10139 For technical conditions C10:UNI 7065-72 Dimensions:From 0,03 mm × 2 mm to 3,5 mm × 350 mm For details click here Packaging:EN 10139 Coil & Cut Lengths - Steel WarehouseEN 10139 steel cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels. These steels are appropriate for cold forming and surface coating. They are not appropriate for hardening treatment followed by tempering.